top of page
OVERVIEW:

The HDE asphalt maintenance vehicle is a turnkey infrared asphalt repair machine that will heat up and soften a localized area of the surface course asphalt, allowing for the area to be re-worked and compacted fixing any surface deterioration. HDE’s highly efficient infrared heaters can soften the surface course ( up to 2.5″) of asphalt to the original mixing temperatures in 5 to 10 minutes without burning the asphalt. The asphalt can then be scarified and the re-rolled to form a seamless watertight repair.

20180522_125220.jpg
20180522_124541.jpg

Potholes, surface cracks, bad joints, bird baths, catch basins, and manholes can be economically repaired with minimal time expended and minor traffic re-routing throughout the year. The HDE asphalt heaters have also proven well for pre-heating of the asphalt for cold weather paving.

HDE infrared trucks provide unique features that you will not find in any other infrared heater on the market.

The HDE Asphalt Reclaimer is capable of both maintaining the temperature of virgin asphalt and reheating cold material to workable temperature. The HDE Asphalt Reclaimer can be used 365 days a year whether it is using material from the local asphalt plant or recycling left- over material to create a hot patching material in the middle of the winter. Reheating left over materials eliminates the need of disposal and can drastically reduce the amount of cold patch material needed to repair problem areas. The reheating process can take 8-12 hours depending on the ambient temperatures and the amount of asphalt that is being heated. By using a digital temperature controller we are able to heat the asphalt safely until it has reached the desired temperature. The controller prevents any burning of the asphalt by turning the heaters of at a pre-set temperature (i.e. 300 ° F).

Orange-Recycle-for-Banner.png

PAVEMENT MAINTENANCE TRUCK

OPERATION

The HDE system allows the operator to heat for a period of 10 minutes. The first five minutes runs on high mode (35 PSI ) and allows the infrared rays to penetrate through the surface of the asphalt. The next five minutes can be run on low mode (15 -20 PSI), allowing deeper penetration by conduction while maintaining an even heat on the surface without burning the oils in the asphalt. (Competitors units operate on one pressure, preventing the operator to turn the heat down ) This allows the operator to reduce fuel usage throughout the day.

Conventional recyclers with high intensity burners will expose the bitumen and aggregate to very high temperatures in proximity to the heat source, even if the heat is indirect. If the temperature of the bitumen goes beyond 275°F (175°C) the light oils start to burn off and the bitumen becomes more brittle. This is especially critical with aged bitumen in RAP that has already oxidized over the years.

FEATURES ONLY AVAILABLE ON HDE HEATERS:

LARGEST HEATER DECK ON THE MARKET (INCREASED PRODUCTION)

INCREASED PATCH SIZE ( FOOTPRINT ) COMPARED TO COMPETING MODEL

STAINLESS STEEL HEATER SKIRTS

FULLY ADJUSTABLE HEAT FOR VARIOUS JOB CONDITIONS

HEIGHT ADJUSTABLE HEATER DECK FOR VARIOUS JOB CONDITIONS

LIQUID PROPANE TO ELIMINATE TANK FREEZE UP AND DECREASES FUEL USAGE

UP TO 10 INDEPENDENT HEAT ZONES TO CONTROL THE SIZE OF YOUR PATCH

20180522_142854.jpg
20180522_125817.jpg

NO BLOWERS

The HDE heaters run on the natural vapor pressure from the vaporizer, getting the correct air/gas ratio without using blowers and batteries, so the operation is simpler and more economical than other designs. The HDE design uses a Venturi design to uses air from the atmosphere to mix with the propane gas. This creates the ideal mixture of propane and air to burn at the correct temperature to create an Infrared Heat Wave. This is confirmed with the picture below showing the IR heater with a output of 1046 °C. This create a IR heat wave that will penetrate into the entire surface course of the asphalt.

MAINTENANCE AND PARTS

All of HDE’s equipment is built with standard gas components, available at gas suppliers throughout North America, if we are unable to meet your delivery requirements. HDE stocks replacement parts and do recommend consulting us prior to making other purchases. Most customers can receive parts within 2 days for US orders and next day for Canadian orders.

FEATURES
Infrared%20Heater%20half_edited.jpg

ADJUSTABLE TEMPERATURE

HDE's heaters are capable of running at pressures of 5 PSI up to 40 PSI. HDE's unique High/Low system allows the operator to heat the patch with a higher temperature for the first 5 minutes, followed by 5 minutes of low heat. This enables the operator to reduce the fuel usage while the heat is penetrating deeper into the already heated patch.

Infrared%20Heater%20half_edited.jpg
CARTRIDGE%20SYSTEM_edited.jpg

PATENTED CARTRIDGE SYSTEM

• HDE's replaceable ceramic cartridge allows for easy replacement of the   heating element

• Typical cartridge life is about 1,500 hours, and can be changed in less than 20   minutes

• This patented design prevents the heat from transferring to the heater   plenum (top), thus extending the life of the heater

bottom of page